Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Blog Article
What are your insights and beliefs on How to Install a Bathtub Yourself?
Mounting a bath tub isn't specifically rocket science, however it does require solid plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a reasonably tough job. If the old bathtub is conveniently available, the project can relocate easily; if you have to open a wall surface to remove the old bathtub as well as place the new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will need an assistant to move out the old bathtub and set in the brand-new one. Make sure you have actually certified yourself for the job and fit attempting it. Rather than employing a specialist to take control of a halfway-completed job, it is far better to take into consideration utilizing one prior to you start. Chances are you might require an expert plumber to make tube links.
This write-up will assist you set up a brand-new bath tub in your shower room if you have already gotten a brand-new tub as well as do not require to change the plan of your previous water pipelines.
Your tools and product list must comprise the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the water system. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of removing the existing taps can be fairly problematic because of the limited accessibility that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a towel all set for the remaining water that will certainly come from the pipes. When the supply pipes have actually been eliminated, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from transforming during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any old securing compound.
Before proceeding to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the other end gives a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making sure that the washing machines are in location between the tap and also the sink. Safeguard the tap in place with the maker offered backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular faucet connectors. The former type must be linked to the faucet ends initially, tightening only by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Mounting the Bath tub
Utilizing both wooden boards under its feet, position the bath tub in the needed placement. The wooden boards are useful in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little factors.
The next objective is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the tub up until the level reads level.
To install taps, fit the bottom of the outermost versatile tap port to the proper supply pipe by making a compression sign up with; after that do the very same for the other tap.
Turn on the water supply and also inspect all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the tub as well as additionally examine the overflow electrical outlet and the regular electrical outlet for leaks.
Ultimately, fix the bathroom paneling as described in the maker's user's manual. Tiling and also securing around the tub should wait till the bathtub has actually been used at the very least once as this will certainly settle it right into its final setting.
Preparing for the Setup
Firstly, the supporting structure supplied with the bath needs to be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you use every one of the provided washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be suited its final placement.
Tiling Around the Bath tub
In the area where the bathroom meets the tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a stiff seal, causing the water to pass through the wall surface in between the bathroom and also the tiling, bring about complications with wetness and also feasible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your fixtures and also fittings. They are sold in tubes as well as cartridges, and also can securing gaps as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to securing, to permit the activity experienced when the bathtub is in usage. The sealer can break relatively early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were shown that editorial about Tools You Need to Install a New Bathtub through an associate on another web blog. Remember to take the opportunity to share this page if you enjoyed it. We love reading our article about Installing A Bathtub.
Book Appointment Report this page